An Ingersoll Rand MTC (Multi-Tool Controller) can use barcode data to identify tightening results or select a Job.
This article explains how to connect and assign a USB barcode scanner, enable barcode capture for a tool, and configure barcode-based Job selection.
Before You Begin
Confirm that:
- You have access to the controller with permission to change its configuration.
- The intended tool is paired with the controller.
- The scanner supports a USB HID interface and a carriage return/line feed (CR/LF) suffix.
- You have the scanner manufacturer’s instructions for configuring those settings.
- You know whether barcodes will select Jobs, or support both functions.
- Any Jobs required for barcode selection have been created and assigned to the intended tool.
For initial installation, see Setting Up an MTC Controller for the First Time.
For programming instructions, see Creating a Pset and Job Using an MTC Controller.
Before changing a production configuration, follow your backup requirements. See Performing a Backup and Restore Using the MTC Controller.
Interface note: Menu names, available settings, and screen layouts can vary with the controller software and connected devices. The demonstration video shows an earlier software version.
Tools & Materials
- MTC controller and compatible paired tool
- USB barcode scanner configured for HID operation with a CR/LF suffix
- Scanner configuration instructions
- Representative production barcodes
- Approved barcode format and Job-selection requirements
Understanding Barcode Capture and Job Selection
Barcode capture and barcode-based Job selection require different configuration steps.
- Barcode capture allows scanned information to be associated with tightening results.
- Barcode-based Job selection uses configured barcode criteria to select a Job for a tool.
Enabling barcode capture alone does not configure external Job selection. For that function, you must also define the selection criteria and set the tool’s Job Selection mode.
Video Demonstration
For the accessory and barcode portion, begin at approximately 21:30 and continue through approximately 26:30.
The video provides an interface demonstration. Use the written procedure below for scanner preparation and barcode-based Job selection.
Procedure
1. Configure and Connect the Scanner
- Use the scanner manufacturer’s instructions to select the HID interface.
- Configure the scanner to send a CR/LF suffix after each scan.
- Turn on the controller and log in with the appropriate permissions.
- Connect the scanner to an available USB port on the controller.
- Wait for the controller to display the device-identification prompt.
If the scanner is not recognized, check its interface configuration and USB connection before proceeding.
2. Name and Assign the Scanner
- In the device-identification prompt, expand the device-name dropdown.
- Select + / Add Name.
- Enter a descriptive name for the scanner.
- Select OK.
- Open Accessories and locate the scanner.
- Review its device assignment and confirm that it is associated with the intended tool or tools.
Use a name that helps distinguish the scanner from other connected accessories, particularly on a controller used with multiple tools.
3. Enable Barcode Capture for the Tool
- Open Settings → BCODE/VIN.
- Select the intended tool.
- Enable barcode operation.
- Select the scanner as the Barcode Source.
- Select the Save icon.
The tool is now configured to receive barcode data from the selected source.
4. Verify Barcode Capture
- Scan a representative barcode.
- Complete a controlled tightening cycle using the intended tool and Job.
- Review the resulting cycle record.
- Confirm that the expected barcode is associated with the result.
The existing IR setup instructions state that the next scanned barcode is attached to the end-of-run result. Verify the required scan-and-tighten sequence for your application before releasing the configuration for production.
If barcodes are used only for result identification, proceed to Validate the Completed Configuration below.
5. Define Barcode Criteria for Job Selection
- Open Settings → BCODE/VIN.
- Select the intended tool.
- Confirm that barcode operation is enabled and the correct source is selected.
- Open Barcode Criteria.
- Select the required Job Name.
- Configure the Start and End fields to identify the portion of the scanned barcode used for selection.
- Enter the barcode-selection text in the Barcode String field.
- Select Add.
The selection text must match the barcode portion defined by the Start and End fields.
For example, the existing IR instructions demonstrate selecting a Job when the first two characters of the scanned barcode are 57. That is a configuration example; use the barcode positions and values approved for your application.
6. Configure the Identifier Requirements
- Expand Identifier 1.
- Enter the identifier Name.
- Configure Length and Length Check according to the required barcode format.
- Select the Save icon.
- Configure additional identifiers if required and supported by the installed software.
The existing IR instructions describe support for two additional identifiers. Use the on-screen Help (?) control for definitions of the available parameters.
7. Enable External Barcode Job Selection
- Open Wireless Tools.
- Select the settings or edit control for the intended tool.
- Locate Job Selection.
- Select External BCODE/VIN.
- Select Save.
The tool is now configured to use the external barcode selection method.
Confirm that the required Job is valid for and assigned to that tool. See Creating a Pset and Job Using an MTC Controller.
8. Validate the Completed Configuration
- Scan a barcode that meets the configured criteria.
- Confirm that the intended tool selects the correct Job.
- Verify the selected Job before operating the tool.
- Complete a controlled tightening cycle.
- Review the result and its barcode identification.
- Repeat the check for each configured Job-selection pattern.
- Test nonmatching or incorrectly formatted barcodes according to the approved validation procedure.
- Confirm that scanner assignments do not affect unintended tools.
Release the configuration for production only after barcode capture and Job selection behave as required.
Expected Tool Behavior
When configuration is complete:
- The scanner appears as a named accessory.
- The intended tool receives barcode data from the selected source.
- Scanned identification is associated with the applicable tightening result.
- A matching barcode selects the configured Job when External BCODE/VIN is the tool’s Job Selection mode.
Other tool-enable conditions or interlocks can still prevent operation after a Job is selected.
If Barcode Capture or Job Selection Does Not Work
Check the configuration in this order:
- Scanner configuration: Confirm HID operation and the CR/LF suffix.
- Device recognition: Confirm that the scanner appears in Accessories.
- Tool assignment: Check that the scanner is assigned to the intended tool.
- Barcode settings: Confirm that barcode operation is enabled and the correct source is selected.
- Selection criteria: Check the barcode string, character positions, and identifier requirements.
- Job availability: Confirm that the required Job is valid for and assigned to the tool.
- Job Selection mode: Confirm External BCODE/VIN when barcode-based selection is required.
- Saved configuration: Confirm that changes were saved.
Use the installed software’s on-screen Help to clarify field definitions. If behavior differs from the instructions, review the applicable software release notes before changing the configuration further.
When to Contact Technical Support
Contact Ingersoll Rand Technical Support if the scanner remains unrecognized, valid scans do not select the intended Job, or barcode information is missing or associated with the wrong result after configuration checks.
Include:
- Controller model and application version
- Tool model and serial number
- Scanner manufacturer and model
- An example barcode, with sensitive information removed
- Screenshots of scanner assignment, barcode criteria, and Job Selection settings
- A description of the expected and observed behavior
Submit a Technical Support Request
Manuals & Downloads
- Setting Up an MTC Controller and QX Tool for the First Time (PDF)
- Creating Psets and Jobs Using an MTC Controller (PDF)
- Pairing QX Tools to an MTC Controller (PDF)
- Backing Up and Restoring an MTC Controller (PDF)
- Setting Up a Barcode Scanner on an MTC Controller (PDF)
- Setting Up Ethernet/IP on an MTC Controller (PDF)
Need Help?
If assistance is needed in the product selection process, please contact Ingersoll Rand's Power Tool Technical Support Team through Submit a Request via our Help Center, email at IRToolHelp@irco.com, or call us at 800-TOOL-HLP (800-866-5457).
Comments
0 comments
Please sign in to leave a comment.