The Ingersoll Rand MTC (Multi-Tool Controller) platform uses Psets and Jobs to organize tightening programs.
A Pset defines the tightening parameters and operations. A Job organizes one or more Psets for an application, including their sequence and applicable batch requirements. Assigning the Job to a compatible tool makes that program available for use.
This article explains how to create a Pset, include it in a Job, and assign the Job to a paired tool.
Safety Notice
Programming changes can affect tool operation and tightening results. Use parameters approved for the fastening application, coordinate changes with production personnel, and validate the completed program before releasing it for production.
Important: Do not use the demonstration video’s example torque, angle, speed, or batch values as application recommendations.
Before You Begin
Confirm that:
- You have access to the controller with permission to change programming.
- The intended tool is paired with the controller.
- You know the tool type and the approved tightening requirements.
- The controller and tool have compatible software.
- You have identified how the tool will receive its Job selection.
For initial installation, see Setting Up an MTC Controller for the First Time.
If the tool is not paired, follow Pairing QX Tools to Ingersoll Rand Cordless Controllers.
Before changing an existing production configuration, follow your backup requirements. See Performing a Backup and Restore Using the MTC Controller.
Interface note: Screen names and available parameters can vary with the controller software, tool type, and licensed features.
Tools & Materials
- MTC controller and compatible paired tool
- Access through the controller interface or a connected browser
- Approved tightening parameters and Job requirements
- Suitable equipment and a representative joint for application validation
Understanding the Programming Sequence
Complete the workflow in this order:
- Create the Pset: Define the tightening operation.
- Create the Job: Select the required Psets and configure their sequence.
- Assign the Job: Make it available to the intended tool.
- Verify Job selection: Confirm how that tool selects the Job.
- Validate the program: Check operation and tightening results before production.
Saving a Pset alone does not complete the workflow. The Pset must be included in a Job, and the Job must be assigned to a compatible tool.
Video Demonstration
For this procedure, begin at approximately 6:00. Pset programming is followed by job creation and assignment at approximately 14:00–17:00.
The video shows an earlier software version. Menu layouts and available options may differ from the installed version.
Procedure
1. Create a Pset
- Open the main menu and select Pset to display the Pset List.
- Select the + control to create a Pset.
- Enter a descriptive Pset name.
- Open Advance Settings.
- Select the Tool Type that matches the intended tool and application.
- Review any additional settings required for the application.
Use names that help distinguish the operation from other programs. For example, identify the component or fastening operation rather than using a name such as “Test” in a production configuration.
2. Configure the Tightening Operation
- Return to the Pset configuration screen.
- Select Forward Operation.
- Add or open the required tightening step.
- Select the step’s edit control or right arrow to open its parameters.
- Select the appropriate Step Type.
- Enter the approved target and applicable limits.
- Review the remaining parameters available for that step, such as rotation direction, speed, angle-counting threshold, and timeout.
- Select Save Step.
- Return to the Pset configuration screen and select the Save icon.
Available parameters depend on the selected step type and tool. Review all applicable fields before saving.
3. Review Trace Settings, if Required
The demonstration includes Trace Settings within Pset configuration. These settings control the available trace-capture options.
If tightening traces are required:
- Open Trace Settings.
- Review whether trace capture is enabled.
- Configure the applicable capture and transfer options according to the application’s data requirements.
- Save the Pset after making changes.
Do not assume that a trace will be available simply because the tool has completed a cycle. Capture settings and system configuration affect the recorded information.
4. Create a Job
- Open the main menu and select Job to display the Job list.
- Select the + control.
- Enter a descriptive Job Name.
- Select the + control beside Select Pset(s).
- Select the required Pset or Psets.
- Select the back arrow to return to the Add Job screen.
Confirm that the selected Psets match the intended application.
5. Configure the Job Sequence and Batch Requirements
- Review the Psets included in the Job.
- Confirm their required sequence.
- Open the applicable Pset entry within the Job.
- Set the Batch Count required for that operation.
- Review any applicable socket assignment, reset behavior, retry limits, or failure rules.
- Review Job-level interlocks where required.
- Return to the Job screen and select the Save icon.
The demonstration shows options such as Max Attempts Enable, Max NOK, and Fail Rules. Configure these only according to the approved process requirements.
6. Assign the Job to a Tool
- Open the Job list.
- Use the Select Tool dropdown to choose the intended paired tool.
- Locate the saved Job.
- Confirm that the Job is valid for the selected tool.
- Use the assignment control to assign the Job to that tool.
If the Job is not valid for the selected tool, review the tool type and Pset configuration before proceeding. Do not substitute another tool or change application parameters merely to make the Job assignable.
7. Confirm the Job Selection Mode
- Open Wireless Tools.
- Open the intended tool’s settings.
- Review Job Selection.
- Select the mode required for the installation.
- Save any changes.
- Select or request the intended Job through the configured selection method.
A Job may be assigned correctly but still require selection through an external device or system.
For barcode-based selection, see Setting Up a Barcode Scanner on an MTC Controller.
For integrated applications, follow the relevant communication procedure:
- Setting Up Ethernet/IP on an Ingersoll Rand Cordless Controller
- Setting Up PROFINET on an MTC Controller
- Setting Up Open Protocol on an MTC Controller
8. Validate the Completed Program
- Confirm the correct tool and Job are selected.
- Review the Pset targets, limits, sequence, and batch requirements.
- Perform controlled validation using the approved application procedure.
- Check that tightening results meet the application’s acceptance criteria.
- Verify batch progression and any configured interlocks or failure-handling behavior.
- Review captured traces if they are part of the validation requirements.
- Release the program for production only after validation is complete.
Expected Tool Behavior
When configuration is complete:
- The saved Pset appears in the Pset list.
- The saved Job contains the intended Psets.
- The Job is assigned to the correct compatible tool.
- The configured selection method makes the intended Job active.
- The tool follows the programmed operations and applicable batch requirements.
Other enable conditions, interlocks, or system faults can prevent operation even when the Job is assigned.
When to Contact Technical Support
Contact Ingersoll Rand Technical Support if a Job remains invalid for a compatible tool, saved settings are not retained, or the tool does not follow the selected program after configuration and enable conditions have been checked.
Provide the controller model and software version, tool model, selected Job, and a description or screenshot of the issue.
Submit a Technical Support Request
Manuals & Downloads
- Setting Up an MTC Controller and QX Tool for the First Time (PDF)
- Creating Psets and Jobs Using an MTC Controller (PDF)
- Pairing QX Tools to an MTC Controller (PDF)
- Backing Up and Restoring an MTC Controller (PDF)
- Setting Up a Barcode Scanner on an MTC Controller (PDF)
- Setting Up Ethernet/IP on an MTC Controller (PDF)
Need Help?
If assistance is needed in the product selection process, please contact Ingersoll Rand's Power Tool Technical Support Team through Submit a Request via our Help Center, email at IRToolHelp@irco.com, or call us at 800-TOOL-HLP (800-866-5457).
Comments
0 comments
Please sign in to leave a comment.